Make sure that you don’t over tighten your hardware. Tighten them until they are flush with the top of the deck, but don’t counter sink them to where the top of the bolt is below the top of the deck.
How tight should trucks be attached to deck?
This is because (1) skateboard trucks tend to be pretty tight right off the shelf and (2) beginners especially feel uncomfortable on loose trucks — but that’s not a good thing. The Real Answer is: Tight enough that you can easily control the board, and loose enough that you can easily control the board.
How do I tighten my skateboard bolts?
Use a skate tool or other useful tool to tighten or loosen the big nut in the center of the truck.
- Turn it clockwise to tighten the trucks, getting tighter turning.
- Turn it counter-clockwise to loosen the trucks, getting a softer turning feel.
What size bolts do skateboarders use?
The standard bolt size is 10-32. 10 refers to the standardized sizing by ANSI B1, and 32 refers to the thread count. There are 32 threads per inch. You’ll use bolt sizes in the 1-2″ range for most setups.
Can you over tighten skateboard hardware?
Make sure that you don’t over tighten your hardware. Tighten them until they are flush with the top of the deck, but don’t counter sink them to where the top of the bolt is below the top of the deck.
How do you know if your truck is too tight?
In most situations, tight trucks are a hinderance. They inhibit your ability to turn and make it difficult to line up on an obstacle. If you often find yourself having to press down on the tail when turning, it’s probably time to loosen the kingpin nut.
Should a skateboard be wobbly?
A wobbly skateboard isn’t a bad thing, some actually like to ride their trucks super loose. Beginners will have a harder time learning to ride a skateboard with loose trucks. After all, a more stable board will help you keep your balance. Just be sure to break bushings in and don’t tighten them until you squish them.
Should longboard trucks be loose or tight?
The trucks should be as loose as you feel comfortable when you’re first starting out. Be sure not to compress the bushings when adjusting your trucks. Once you’re comfortable with your board, loosen your trucks up a hair so that they feel slightly uncomfortable.
How tight should my skateboard be?
For stability while cruising, medium tightness is preferable. This should keep the trucks loose enough for turning. However, tighten the trucks if you tend to skate downhill or plan to do some practice rides on a steep slope or ramp.
Should skateboard wheels be tight or loose?
Wheels are attached to the axels with a single nut (1/2″) per wheel. The nuts should be tightened as far as they can be without impeding the spin of the wheel. Generally you should feel only a very minor amount of play if you try to move the wheel side to side.
What size bolts for 8 deck?
Skateboard Deck Size & Hardware Size
If you skate and 8.0″ deck, you still can use 7/8″ hardware without risers.
What type of bolts are used in skateboards?
To skate, you only need countersunk bolts. This type of bolt is set in the deck to form a smooth surface that won’t interfere with your skating. Raised head bolts are especially suited for drop-through longboards and special materials in longboard construction.
Can you reuse skateboard hardware?
The bolts can be reused. The locknuts are really only good for locking once.
What size trucks do you need for a 8.25 board?
Which trucks do I need? If you’re setting out to buy new trucks, you’ll find that each brand labels trucks differently. That means if you ride an 8.25-inch board then you’d need Independent 144s, Thunder 148s or Venture 5.6s (each have an axle length of 8.25-inches).
What size wheels should I get for a 8.25 deck?
52 – 55 mm
FIND THE RIGHT SIZE SKATE PARTS
| Deck Size | truck Size | Wheel Size |
|---|---|---|
| 8.0 | 7.75 – 8.25 Axles | 50 – 54 mm |
| 8.125 | 8.0 – 8.25 AXLES | 50 – 54 mm |
| 8.25 | 8.0 – 8.5 axles | 52 – 55 mm |
| 8.375 | 8.25 – 8.5 axles | 52 – 55 mm |
Do loose trucks cause speed wobbles?
CJ: For starters, speed wobs can be caused by a number of different reasons. A common one being loose trucks. Loose trucks can give you too much turning ability, making your set up hyper-responsive for any speed over 10-20mph. If you’re going faster than that, then you just might want to tighten your trucks.
How do I tighten my truck without a skate tool?
As an alternative to the skate tool, take out:
- Wrench – Designed to tighten bolts and nuts.
- Pliers – Pliers may also be used; just be sure that it is enough to grip the nut on both sides, so you can tighten it or loosen it regarding your preference.
Why do loose trucks save lives?
Looser trucks enable you to turn and respond to situations better. Though you are more prone to speed wobbles with looser trucks, more experienced riders are able to prevent wobbles because of their stance, ankle strength and ability.
Do skateboard trucks loosen over time?
Do Skateboard Trucks Loosen Over Time. Yes, definitely they have the tendency to loosen over time so it is your job as the skateboard owner to check your truck’s condition every now and then. Skateboarders tighten their trucks based on their own preferences.
Why does my skateboard lean so much?
If your skateboard is constantly turning or leaning towards the left or the right, there are a couple of possible causes. The most likely ones are either the bushings in your trucks, or your hardware. Bushings are the hard, rounded plastic pieces in your trucks that squash down in the direction you are turning.
How do I stop my skateboard at high speed?
Not only is it a cool trick, but it won’t ruin your shoes or deck either. Yes, your wheels will gradually get smaller, but it’s one of the best ways of stopping a high-speed skateboard. The trick is to turn the board from a vertical to a horizontal position and then slide your wheels across the ground.