Remember to aim for 10 to 30 seconds spinning skateboard wheels. In other words, your skateboard wheels should spin freely for at least 10 seconds without stopping. If it stops spinning before 10 seconds, your wheels are tightly placed.
Why is one of my skateboard wheels spin slow?
Chances are you just have to clean and lubricate your bearings. Remove your wheel and pop out the bearings with the edge of your axle. Bones Bearings pretty much set the standard in the skateboarding world as far as bearings go.
Should bearings spin freely?
Bearings should always spin freely and quietly and be free of grime or rust.
Should skateboard wheels wiggle?
Most importantly, they should be tight enough to resist wheel bite and speed wobbles. This makes for a smoother and safer ride. If you enjoy flexing tricks on the skate ramp as much as we do, keeping your wheels moderately tight is the way to go. Learning to flip a skateboard is probably every rider’s aspiration.
Is WD40 good for bearings?
Yes, you can apply any kind of lubricant to the bearings. Be sure to dry any excess once you have sufficiently lubricated the bearings.
Why is my new skateboard so slow?
Dirt and dust buildup and cause friction, resulting in a slower skateboard. Sometimes you don’t even notice how much dirty bearings slow down your skateboard until you cleaned them or even replace them entirely. What is this? While you don’t need top-notch skateboard bearings, quality bearings make a difference.
How long does it take to break in skate bearings?
Like others have said, most bearings require very little break in or none at all. The break in comes from the lubricant. Bearings with a heavier oil or grease lubricant will require a “warm up” to reach their full potential. However, this shouldn’t take long, 30 minutes to an hour at most.
Do bigger skateboard wheels go faster?
Get bigger (taller) wheels
In a race, a skateboarder will get off the line quicker (faster acceleration), but a longboarder will eventually pass them as their taller (bigger) wheels allow them to have a higher top speed.
Does loosening skateboard wheels make it faster?
The first, and easiest method of making skateboard wheels spin faster is to loosen the axle nuts. If they are too tight, they will keep your wheels from spinning freely. You can also clean the wheels and bearings or replace them if necessary.
Should you grease skateboard bearings?
This is crucial because skating a dry bearing will create damaging friction. We recommend using a skate-specific bearing lubricant like Bones Speed Cream or Bronson Speed Co. High Speed Ceramic Oil. Drip 1-2 drops of lube into the bearing, then spin it to evenly distribute the oil.
Do you lube skateboard bearings?
Buying New. In most cases, all you need to do is lube them and spin the wheels but, every once in a while, you need to give your bearings a full cleanup to revive their original characteristics and improve the skating experience.
How tight should I tighten skateboard wheels?
The nuts should be tightened as far as they can be without impeding the spin of the wheel. Generally you should feel only a very minor amount of play if you try to move the wheel side to side. Occasionally a nut might work itself tighter or looser than originally set and should just be corrected.
What wheels does Tony Hawk use?
53-56mm The 53-56mm wheels are the more common wheel size for beginners or bigger riders skating street, skate parks, bowls and vert ramps.
Can I use wd40 on skateboard bearings?
Using some WD-40 Specialist® Degreaser , spray the entire surface of the wheel and ball bearing, and leave it to work for a few minutes. Next, submerge the parts into a bowl of clean water, and leave them to soak for an additional few minutes. Your wheels and bearings should now be grime free.
What happens if you over grease a bearing?
Too much grease volume (overgreasing) in a bearing cavity will cause the rotating bearing elements to begin churning the grease, pushing it out of the way, resulting in energy loss and rising temperatures.
Can you use vegetable oil as lube for bearings?
Vegetable oil should NEVER be used to lubricate mechanical parts. It always leaves a solid deposit which later will be stuck to the parts you wanted to lubricate. Save this answer.
Can you use olive oil as lube for bearings?
Using solvents as lubricants
Remember that olive oil should not be used as a cooking oil on bearings. However, it is preferable to nothing, and far better than using a solvent.
Do bearings get faster?
New bearings require the freshly milled and polished steel balls/races to roll against each other and settle lube into their surfaces. Once a bearing is ridden a few miles, the surfaces will be completely saturated with lubricant. This almost always makes the hand spins faster.
Why does my skateboard only turn one way?
If you find your board consistently going in one direction, it’s likely that the truck on that side is either too loose or too tight. Your trucks should be evenly tightened – this will help them steer you in the right direction.
Do bearings have a break in period?
Why is Breaking In Your Bearings Important? For grease lubricated bearings, the break-in procedure is as important for the grease placement as it is for the bearing races. Proper greasing will place the grease between the balls and the raceway(s).
Do skateboard wheels need to break in?
Longboard wheels are made from softer plastic than standard skateboard wheels. While softer plastic is great for absorbing shock and gripping the road, longboard wheels need some breaking in before you can use them to slide, turn or skid to a stop.