Using a wooden skewer or the plastic punch tool provided in your pumpkin-carving kit, transfer the photograph to the pumpkin by poking a series of close holes through the paper and directly into the flesh of the pumpkin.
How do you transfer a photo from paper to pumpkin?
Apply Water. Use a damp sponge or spray bottle full of water to soak a small area of paper (Image 1). Gently begin to rub away the paper with your finger (Image 2). You’ll notice the black image has transferred to the pumpkin.
Does transfer paper work on pumpkin?
It’s so simple!
The Fabric is recommended for carving just about any graphic onto watermelons and for carving simple bold patterns onto pumpkins. However, because the Transfer Pattern Fabric is water soluble, the Pattern Transfer Paper is recommended when carving juicy pumpkins with detailed patterns.
How do you attach a paper stencil to a pumpkin?
Tape the paper to the pumpkin, then score the design onto the pumpkin by punching through the paper into the pumpkin flesh with a large nail. With a sharp serrated knife, cut out the design using the punched holes as a guide. Remove the cut-out pieces by pushing them out from the inside of the pumpkin. Congratulations!
How do you Modge podge pictures on a pumpkin?
Instructions
- Print about 50 of your favorite photos in black and white on regular paper.
- Paint a thin layer of Mod Pog on the back of a photo then place on the top of the pumpkin.
- Continue adding pictures on, layering from top to bottom until the entire pumpkin is covered.
How do you put designs on a pumpkin?
Use your one free hand to flatten a small piece of a stencil at a time, and work your way around the design. If you plan to carve, poke holes every 1/4 inch or so with your poking tool or pushpin. You can also use an X-Acto blade to trace and cut through the design, scoring the pumpkin in the process.
How do you put a logo on a pumpkin?
Put your logo on a pumpkin (and impress coworkers)
- Step 1: Pick a pumpkin, wash it, and let it dry.
- Step 2: Print your company’s logo and cut it out.
- Step 3: Loosely tape the stencil on the pumpkin and trace it.
- Step 4: Paint the logo, one color at a time.
- Step 5: Proudly display your masterpiece.
How do you scrape a pumpkin design?
To carve a design in relief, first clean your pumpkin and cut out a lid. Remove the pulp from the pumpkin and scrape the inside. Then, draw your design on your pumpkin using avgrease pencil or dry-erase marker. You may also want to cut along your design using a utility or craft knife.
How do you make a pumpkin template?
Pumpkin Stencil Steps:
- The finished pumpkin stencils.
- Open the image in Photoshop.
- Select the image.
- Paint your image a solid color.
- Select image background.
- Erase the background.
- Export the image as PNG.
- Open your new pumpkin stencil in InDesign or Word.
Can you Modge podge paper to pumpkin?
Once you have the pumpkin covered with Mod Podge and scrapbook paper, you’re ready to smooth it down. I went over it good with my fingers pushing the Mod Podge covered paper down. Since it’s wet from the Mod Podge, it’s pretty easy to smooth it down to form around the pumpkin.
Does Modge podge work on pumpkins?
Simply cut strips of your paper (approximately 1″ wide), apply a coat of Mod Podge to a small section of your pumpkin, and apply your strips to your pumpkin, making sure it adheres completely. Once you’re pumpkin is covered, let dry, and apply a thin coat of Mod Podge to seal.
Can I use Mod Podge on a pumpkin?
Brush a medium layer of Mod Podge down onto the pumpkin. Lay down the map strips and allow to dry for a few minutes. Brush a thick layer of Mod Podge on top of the strips. Continue to overlap the map strips and secure with Mod Podge.
How do you easily scrape a pumpkin?
Use an ice cream scoop to gut your pumpkin. Not only is this tool designed specifically for scooping, but the sharp edges are perfect for scraping the sides of your pumpkin if you want to thin them before carving.
Do you cut the black or white of pumpkin stencil?
Trace stencil with a dull pencil or poke through paper with a thumbtack to transfer image. Make sure to trace shadow lines and inside shapes onto pumpkin as well. Remove stencil and mark which areas should be cut out (white), scratched (gray), or left alone (black).
What tool do you use to scrape a pumpkin?
Serrated Knife: The saw-like blade of a serrated knife is perfect for removing large areas from pumpkin flesh.
Can you use a hot knife to carve a real pumpkin?
Carving Your Design
Preheat your hot knife. Use the hot knife to cut the top off the pumpkin. As with real pumpkins, I like to cut it in an asymmetrical way, angling the knife inward as I cut. In sections, use the hot knife to cut away the parts of the pumpkin to be removed.
How long do shaved pumpkins last?
three to five days
Once carved, pumpkins will generally only hold up for three to five days — or up to two weeks if you live in a colder climate — before wilting and showing signs of decay. And that’s not very long when you’ve worked so hard on your masterpiece.
What do you bring to a pumpkin carving party?
The fond memories made at this special event are gift enough.) BYOP. Make sure that everyone knows to bring their own pumpkin, pumpkin carving kit, and candles. Prep the carving areas before they get there.
Can I decoupage a real pumpkin?
To create a decoupaged pumpkin, you will need a pumpkin, white acrylic spray paint, decorative napkins, glitter, Mod Podge, scissors and a paintbrush. First paint your pumpkin and let it dry. Meanwhile, cut out the desired shape from your napkin (only use one layer).
How do you get paint to stay on a pumpkin?
Next, clean your pumpkin so that the paint will stick to the surface. “It’s a good idea to wash the pumpkin and dry it really well,” says Evan. “That way, you’re not putting paint on a fine layer of dirt—you’re putting paint right on the skin of the pumpkin.”