We would like to let you know it is not recommend to wash out the dust cup. We recommend using a dry cloth or paper towel to wipe out the dust cup.
Can I wash the canister on my Shark Navigator?
Empty the Dust Canister
Soak the canister in soapy water and wash it using your microfiber cloth. Rinse it in cold water and allow it to air-dry. Be sure the canister is completely dry before reassembly.
How do you clean the brush roll on a Shark Navigator?
Shark Navigator And Rotator Powered Lift-Away
- You still need to remove the compartment hosting the brush roll first (also known as the brush roll garage).
- Turn off and unplug the machine.
- Pull the tab on the left side of the brush roll to lift it up.
- Give the brush roll a wash as needed and let it dry completely.
What is the dust cup on Shark vacuum?
Description. A replacement dust cup for your Shark® Rocket® cordless stick vacuum. Collects dirt and debris while you clean and makes emptying easy with its CleanTouch™ Dirt Ejector.
Why does my Shark vacuum smell?
Roller Brush is Broken or has Debris
Once the vacuum has cooled check the roller brush for any damages or any debris. If you notice any debris you will have to clean the roller brush. Any damages to the roller brush can cause the vacuum to emit a burning odor.
Why does my Shark robot keep saying the dust cup is missing?
A: It happens because the dust cup isn’t fully emptying at the dock, probably because the suction is too low. Try cleaning the filters on the right side of the dock.
Where is the Shark robot dust cup?
Step 1 Dust Cup
It is right next to the power button at the base of the handle.
How do I get the dog smell out of my Shark vacuum?
How To Get Pet Smell Out Of A Vacuum Cleaner
- Change the filter or wash it.
- HEPA filters are best.
- Put a dryer sheet inside the bag or similar.
- Sprinkle baking soda on your carpet and vacuum. Swap out the baking soda for cinnamon.
- Wash out the hose.
- Check the brush head and release caught up hair.
Why has my Shark vacuum lost suction?
If both your foam filter and felt filter have not been cleaned in the past month, this may be why your vacuum has lost suction. To clean the foam and felt filters, remove the dust cup and pull out the two filters that are on the top of the motor base. Rinse the filters with lukewarm water until the water runs clear.
What happens if my Shark Hoover gets wet?
It is very important to let it dry thoroughly before using it again. If you start vacuuming again too soon, the water can reach mechanical parts, after which the vacuum cleaner can irreparably break.
How do I clean my Shark Navigator Lift Away deluxe vacuum?
1 Dust Cup Empty each time you vacuum. 2 Pre-Motor Foam Filter Rinse and air-dry every 3 months under normal use. 3 Pre-Motor Felt Filter Rinse and air-dry every 3 months under normal use. 4 Post-Motor HEPA Filter Clean once every 2 years or as needed.
How do you clean a Shark filter?
To clean foam and felt filters, simply tap off loose dirt, then rinse them under a tap. Only use water – do not use soap. Always let the filters air dry completely before reinserting them. You can also tap loose dirt off filters between washes as needed.
Is it OK to wash vacuum filter?
Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn’t need to use any detergent – just water.
Can I wash Shark vacuum filters?
All of the filters that come with your Shark vacuum, including HEPA filters on models that include them, can be cleaned or washed for re-use.”
Can you get a vacuum filter wet?
Paper filters should never be soaked or rinsed in water. However, some filters are made from a non-woven synthetic material (similar to a dryer sheet) that can be rinsed with water a few times to remove dust. To extend the life of a pleated paper filter: Remove it from the vacuum.
Can you remove brush roller from shark vacuum?
Step 2: Removing the Roller Brush
Once you push the lever, the roller pops out. It’s something to keep in mind. Once you have the roller out, it’s easier to clean. Shark recommends only using water to wash the roller and drying thoroughly before returning it to the vacuum.
Why is my Shark Navigator brush roll not working?
If the roller brush is not clean, an accumulation of debris can be blocking its movement. To clean the roller brush, carefully cut out the debris accumulated around the roller brush. Once clean, check if the brush is intact. Additionally, the roller brush may not be spinning because the motor stopped running.
What is a dust cup?
Dust cups are an optional tooling accessory that provides a secondary barrier to the upper punch seals. Dust Cups prevent oil and other debris from contaminating granulation. There are two styles of dust cups, barrel-style and standard.
How do I clean my Shark anti hair wrap?
Tap off any loose debris, use a dry towel to wipe the brush-roll clean and remove any debris caught in the teeth behind the brush-roll. Hand wash if needed, using only water, and let it air dry completely for at least 24 hours before reinserting.
Why does my Shark robot keep saying the dust cup is missing?
A: It happens because the dust cup isn’t fully emptying at the dock, probably because the suction is too low. Try cleaning the filters on the right side of the dock.