5/8 (Shallow) grind is what most figure skaters skate on. This gives you a good flowing edge and has little friction on the ice.
What size skate sharpening should I get?
A Guide to the Recommended Skate Sharpening Radius
The 1/2″ radius would be our typical recommendation because it is the perfect blend of “glide” and “bite.” Some players opt for the 3/8″ cut, but you are definitely sacrificing some “glide,” which can in turn affect your overall speed on the ice.
What is the normal skate sharpening?
The normal range for this is ⅜” to ¾”, although higher or lower hollows are occasionally seen. Typically, skate shops will do 1/2”, 5/8”, or 7/16” hollow as a default if they aren’t given any specific instructions.
How thick should your skate blade be?
If you are very lightweight, a 3/8” radius is probably what you need. Light to average weight skaters typically have a radius of 1/2″ to 5/8” while heavier skaters usually opt for about 3/4″ to avoid chattering when they try to stop.
What is the most common skate sharpening radius?
½” and 5/8”
The most common radius of hollow cuts are ½” and 5/8” for skate sharpening shops because it provides the best balance between edge depth and glide speed.
Is 5/8 a good skate sharpening?
5/8 (Shallow) grind is what most figure skaters skate on. This gives you a good flowing edge and has little friction on the ice. 1/2 (Standard) grind will be a lot more forgiving when landing a jump giving a sharper edge to land on.
What do most NHL players sharpen their skates?
Most skates are sharpened by cutting an arc in between the two edges, known as the radius of hollow (ROH). This is measured in inches. Hockey player and goalie skates are often sharpened with a ROH from 3/8” up to 1-1/2”. Figure skates are generally sharpened to 1”, and speed skates are COMPLETELY FLAT!
Can skates be too sharp?
Extra sharp skates can slow a player down or make transitions difficult. Sharp skates result in a slower glide because the blades sink into the ice more. Skate blades are too sharp when the hollow (the curve between the inside and outside edges) is too deep.
What sharpening Do NHL players use?
It’s a 3-millimeter-wide piece of steel hollowed out down the middle in an inverted U to create two edges. An NHL player uses both edges on both skates, like a skier shifting weight from side to side during turns. Most recreational players just want their skates sharpened.
What is a 3/8 skate sharpening?
Different Types of Skate Sharpening Hollows
For example, a lighter player can benefit from a deeper hollow (7/16″ or 3/8″) by providing them with the ability to cut deeper into the ice. This type of sharpening provides more bite for the user, allowing for more responsive turns/stops and quicker overall acceleration.
How sharp are NHL skates?
Hockey skate blades are sharp enough to cut someone when swung at high speeds but also dull enough that you could softly run your fingers across without even breaking the skin. In fact, it is common for skate sharpeners to use their finger to feel the edge of the blade to make sure the skates are properly sharpened.
Do longer skate blades make you faster?
The longer blades help speed skaters go faster because they provide more pressure into the ice. These blades also help speed skaters have more grip on the ice while they skate.
Why do my feet hurt when I ice skate?
Without thin socks, you can get painful corns and blisters. Lace your skates tight enough so that they fit is snug, but not painfully tight. Lacing boots too tightly can cause lace bite, a condition that causes sharp foot pain due to compressed tendons.
What skate radius is for me?
Forwards generally prefer smaller radius than defense men of the same weight. Goalies generally prefer very large radius so that they can “kick out” without catching an edge. Figure: Most beginner and instructional skaters can skate on a 1/2″ radius. A 5/8″ radius will take care of most recreational skaters.
What is the sharpest skate sharpening?
You can get your skates sharpened anywhere from 1/8th of an inch to one inch. 1/8th would be the sharpest, and one inch would be the least sharp.
How often do NHL players sharpen skates?
A rule of thumb is for every 15 to 20 hours of ice time, but let’s go beyond the basics. The biggest factor is how often you skate, hence the rule of thumb based on ice time. It’s not unheard of for some players to sharpen their blades before every game, and others once or twice a year.
Is 8.5 good for street skating?
8.00″ to 8.50″: Ideal for various street and transition terrain. Parks, pools, rails, stairs. 8.50″ and up: Wider decks great for transition skating, bigger street tricks, pools, or just cruising.
What skateboard size should I get if im 5 8?
Skateboards will be 7.5 – 8.25 inches wide.
Size Boards:
| Board Length | Height Range | Stance width |
|---|---|---|
| 29.5” / 75 cm | Upto 5’6” (167 cm) | 20” |
| 30.3”/ 77 cm | 5’6” – 5’8” (167-172 cm) | 20.8” |
| 31.5”/ 80 cm | 5’8” – 5’10” (172-179cm) | 22.0” |
| 32.7”/ 83 cm | 5’11” – 6’1” (180 – 185 cm) | 23.2” |
What is a 90 75 skate sharpening?
90-75, a very sharp skate, player’s option. 85-75, fairly sharp player’s option. The 50 Series is the lowest FBV groove, giving you the best possible glide. This series contains all of our most popular options. 100-50, a sharp skate for a lightweight junior player, who likes a very sharp skate.
What sharpening does Sidney Crosby use?
(The regular hockey sharpening is ½ inch at most skate shops so you will need to specify the type of sharpening that you want).
Some examples of ROH used by current and former NHL players are:
| Wayne Gretzky – 1/2″ | Sidney Crosby – 9/16″ |
|---|---|
| Joe Sakic – 5/8″ | Evgeni Malkin – 11/16″ |
Do NHL teams use Sparx?
Used by more than 25 NHL teams, the Sparx Sharpener produces professional results with ease.